Results 1 to 2 of 2

Thread: Replacing Your DFI Module In a VR

  1. #1
    Summer-Sickness's Avatar
    Summer-Sickness is offline 2005 VZ EXEC
    Ride
    05 VZ Executive

    Join Date
    Jan 2007
    Location
    Rockingham, Perth
    Posts
    240

    Default Replacing Your DFI Module In a VR

    This write up is how i changed the DFI module in my VR, i would assume VN-VS would have the same method, and most other commodore models would be quite simmilar. I will upload some pics within the next few days.

    What you will need:
    Socket Set
    Replacement DFI module (with or without coil packs attached)

    Lets Get Started!

    Locate the DFI module and Coil Pack.

    Towards the passengers side of the DFI module is a plug, there is a small bolt in the middle, undo this bolt using the appropriate sized socket… from memory it was around 5-6mm, pull out the plug and leave it hanging.

    At the bottom of the DFI module you will notice there are 3 bolts holding it in place, undo these 3 bolts, and before you go any further ensure that your spark plug leads are numbered… if not then using a pen or marker put strokes on the leads I for 1, II for 2 III for 3 etc… pull the spark plugs leads off the top of the block and lift it out.

    Now, If you bought just the DFI module, without the coil packs, you will need to take off your existing coil packs and put them onto your new DFI module, take note of what order they go in… you can either undo them one by one and put each coil across or just draw a quick sketch of the positions, take them all off and bolt them onto the new DFI module, they are held on by 6 bolts, 3 on each side.

    If you bought the DFI module with the coil packs attached (or have now mounted your old coil packs onto your new DFI module) simply pull the mounting plate off the bottom of the existing DFI module and put it onto the other one, might be an idea to give it a bit of a clean off first, then put the spark plug leads back on, bolt the DFI module back on to the mounting plate, put the plug in and tighten up and your done.
    REHAB IS FOR QUITTERS!

    MY 2005 VZ EXECUTIVE

  2. #2
    Summer-Sickness's Avatar
    Summer-Sickness is offline 2005 VZ EXEC
    Ride
    05 VZ Executive

    Join Date
    Jan 2007
    Location
    Rockingham, Perth
    Posts
    240

    Default

    didnt relise this actually made it up n posted it again...
    please delete thread
    REHAB IS FOR QUITTERS!

    MY 2005 VZ EXECUTIVE

Similar Threads

  1. ABS module
    By gopher in forum VT - VX Holden Commodore (1997 - 2002)
    Replies: 29
    Last Post: 13-11-2008, 07:27 PM
  2. dfi module
    By shumway in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 7
    Last Post: 21-10-2008, 09:53 PM
  3. replacing ignition module on a VK
    By VKNutt in forum VB - VK Holden Commodore (1978 - 1985)
    Replies: 2
    Last Post: 19-07-2006, 10:51 AM
  4. module
    By ab56452001 in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 6
    Last Post: 02-02-2006, 07:16 PM
  5. VR V6 DFI Module
    By tommo824 in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 2
    Last Post: 08-01-2006, 10:01 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98