VL turbo gear, trimatic, gt35, big fuel system, haltech etc 10sec setup
LOCATION: victoria, melbourne - out greensbrough way
CONDITION: Used
PRICE: Firm
DELIVERY/PICK UP INFORMATION: pick up would be dine, smaller items can be posted.
PAYMENT OPTIONS: Direct Deposit cash on pick up
CONTACT DETAILS: Email, PM, Phone or Other
ITEM/S:
Hotside
Gt35 garrett ball bearing.
.50 compressor housing, .82 turbine housing
external gate.
rebuilt by rotomaster 2 years ago, done approx 10 000km if that.
no shaft play at all, no damage to compressor blades or turbine, always ran an air filter
$1200
All too suit low mounted gt35/40
Braided feed to suit above turbo $35
Hardline water fitting $25
oil drain- $20
braided/hardline water fitting $35
braided actuator line, with boost controller
all done in dash -4 fittings silver and blue
$120
turbosmart 38mm gate with screamer pipe
vgc
$350
standard sytle turbo manifold with adpation to suit above mentioned turbo smart 38mm also has a 10mm spacer too suit gt35
$150
may done a package deal on the above.
--------------------------------------------------------------------
3" pacemaker pipe, some dints not to bad still works perfect $120
--------------------------------------------------------------------
full 3" catback exhaust with bashed out cat $250
-----------------------------------------------------------------------
90deg intake pipe with pod filter 3" $40
----------------------------------------------------------------------
Chrome plated timing cover, top cover only. never been used, only installed once.
$60
Chrome plated engine removal hooks
one that goes on the back near the oxygen sensor and the other that lives near the coil.
$40
chrome plated dip stick $15
---------------------------------------------------------------------
Trimactic 3 speed
Fully manualised.
one piece tail shaft
3500rpm tce convertor
b&m quick shifter with low mount box
fully rebuilt by yarra vally autos less than 12months ago, actually hasnt even really been run in yet, done around 500km if that
very strong box built with all the best bits too handle 350rwkw
everything you need too convert your vl, bar speedo cable... was on the to do list
also comes with an external oil cooler, davis craig. decent sizes lives under the battry area kina
$3200 - cost me alot more then that and its basically never been used
--------------------------------------------------------------------
MSD blaster coil $80
MSD A6LE i think.. $220
---------------------------------------------------------------------
haltech e6x
custom loom too suit rb30 and have quite a few different base tunes to get you up and running.
comes with 3 bar map sensor and usb to serial port convertor
very good ecu, great plug your laptop in and your away.
$1000
---------------------------------------------------------------------
Jd customs plenum, suit n/a runners
polished with welds showing, comes with 68mm throttle body
and ported n/a runners.
vgc little use.
$700
---------------------------------------------------------------------
no holes intercooler kit suit jd plenum and low mount turbo.
mild steal pipe, 600x300x75 cooler
$220
---------------------------------------------------------------------
Head has had some port work.
just basic stuff by the looks
crow valve springs
wade 1147c camshaft
and machined lifter blocks too suit
less then 500km on the cam/lifter blocks
lifters have been stripped down and cleaned.
$450
---------------------------------------------------------------------
catch can, with breather built in the top.
-6 braided line, fittings to suit standard thread on rocker cover.
lives where the airbox would go.
looks great, works well.
$120
----------------------------------------------------------------------
fuel system gear
built this as a massive overkill fuel system...
twin bosch 044 pumps, 2L surge tank all braided line.
check valves for each pump, pressure guage
-6 fittings, 3/8 fuel lines.
1000cc rochester injectors
aeromotive fuel pressure reg
all done less then 500km
all mounted up on a piece of alloy
includes relays and wiring for pumps.
costs me a monster in braided line and fittings and countless trips to vpw.
depending on interest will sell as a package.. although consider theres around $1200-$1500 in braided lines and fittings alone...
----------------------------------------------------------------------
ebay alloy radiator havent used it... comes with billet style radiator cap
$180
-----------------------------------------------------------------------
pm or email me at vlturbopower@hotmail.com
will post more reasonable sized items...
ie not the auto
aust post limit is like 1m long and 25kgs or something along those lines.
will prob think of loads of other things in the coming days... guess the cars for sale too... dunno how much though
heres the link for pictures of the car as is basically, reason for sale driven it onces this year around the block...
its a waste just sitting here and i want a jetski.
spent all the cash on all the good bits in the past, no crap all in good working order i dont sell rubbish.
cheers tom
Posting Permissions
LinkBack URL
About LinkBacks
