Search results

Ok, thanks, I guess that pretty much answers my questions. My combo is the same as everyone else's (more than likely) with a full exhaust/otr.

Not worried about the price. I just included that to point out I did pay a proper price for it. So it's definitely possible to get a decent tune in that time if they know what there doing. My car is a basic full exhaust/otr combo.

Hi, Just wanted to know how long it takes to do a dyno tune. When I had my vz ss tuned, it took less than an hour. About 1hr 15 mins from the time I arrived till the time I drove out including paying and having a bit of a chat about other mods. I heard the car ramp up about 3 times and rev for...

Where can I download the software from?

I went the drags the other day and ran a 13.6 @102mph in my vz ss A4. I have a mafless tune 308rwhp (230rwkw) with full exhaust and ziggy OTR. I was happy with this but wanted a low 13 sec quarter. So I went and put some 3.7's in and the best I could do again was a 13.6 @ 105mph so this...

Pretty much what the tuner said but I do the same 70km round trip on the hwy even day. The exhaust was on the car when I bought it. Try-y pacies, high flow cats and twin 2.5in exhaust. I have since put new o2 sensors in. Reset pcm

I had a maffless tune done on my VZ SS A4. with full exhaust and OTR. only added the otr at the time of the tune and gained 30rwkw (now 230rwkw) everyone says there getting these great fuel figures in the low 9's with similar mods but mine didn't change at all and sits around 11l/100km's. I...

That's great Thanks

Anyone know if the iat sensors are the same in the v6 ecotec hand v8 ls1. The sensor in the air box. Cheers.

Can I use elm327 adaptor to see? I have a bluetooth and usb adaptor.

Just wondering if there is any way to tell if my car has been tuned before. It's a vz ss. When I bought it it had a full exhaust system on it with stock intake and goes great. No stickers on it anywhere to say it's been to a tuner. Cheers.

I just put an aftermarket h/u in my 04 vz SS and have lost some of the functions of my dash like headlights courtesy on and door lock controls etc. I've done a search and looks like I need a dash software upgrade. Anyone done it or have any other advice. So annoying as I just pulled...

Cpr6 are now $1350 so same price anyway.

Also undo the sway bar but I see you already got it.

I have a 175 alloytec vz, Just after some advise on extractors and cats, will they give me more power or just move the power up the rev range. I've done a search and there's just so much confusion out there. Things I've done so far is cai, 12mm manifold spacers, twin 2.25in catback and mace...

I leave mine in on my VZ.

I think they are just heavy as.

I been doing a bit of googling and reading on here, looks like a few cool things you can do with your dash cluster with custom text or a hsv logo or even a shift light. Found this site - 1337vending - vzclustermod I also see TazzI on here has a program that does it but hasn't released it...

I have one, pretty good, can do a stand still if I wanted to now, not that I do, not my thing. I'm so used to flooring it everywhere to get it moving that now if I drive it the same it will spin the wheels. Not in a straight line take off but going around a corner or powering through a corner...

Look at the 10th number of the V.I.N. If it's a 4 then it's and 04, and if it's a 5 then it's a 05.

I find my vz is in closed loop a lot(using a Bluetooth obd2 adaptor to see its in closed loop). Even under moderate accelerator meaning it's using all the sensors including O2 sensor to control fuel/timing. If your O2 sensors are buggered then so will your fuel economy. Depending on which model...

Yeah pretty simple, the second time I pulled the manifold off I did it in under 1.75hrs including degreasing the whole manifold, cleaning the old gaskets off and removing the throttle body etc. Really is simple.

Pm sent interest in pics.

I put a cat back system off a hsv on mine. Sounds ok but dead quiet at idle and cruise. It's stainless and twin 2.25 and only cost $95, I've heard of people getting them for $1 off ebay.

Thanks, great answer. Do you sell any bolt on extractors? Even with a new cat pipe so I don't need to pay for installation.

There a strange size bolt, my manifold spacers I bought second hand didn't come with bolts, cost me $30 odd for 4 longer bolts. I rand a few bolt shops before I found some long enough.

Hi guys. I'm just trying to find out which extractors to get for my alloytec, got a few quotes from different places (installed) Redback $650 Pacemakers $750 Supercat $695 Cheers. If anyone can recommend anywhere else on Brisbane Northside too would be great.

Ethanol destroys your fuel system, cause bacteria to form in your tank and in general bad. It doesn't clean it, it eats away at it. Yes bp and caltex offer 10% blends called E10 but not in there premium fuels to raise octane. There's no economic benifet from it, fuel economy is much worse on...

Only if you go to those dodgy places, she'll, bp and caltex defiantly don't do this. United 100 is just 98 with 10% ethanol. You would be surprised by what fuels are shared by the fuel companies. Ie, shell gets there 98 from caltex and and diesel from bp etc (these are just examples and...

Ok thanks, i called yesterday and got the info I wanted, I just couldn't get onto turbo industries even though I called a few times. Both tunes sound like what I want and are both the same price. Although with turbo industries they can load the tune onto a autocal so no down time.

Hi mate, can you tell me a bit more about your mail order tune from turbo industries.

I don't mind sending the ecu away. Here's the ones I found. Powerchip Powerchip Partnumber FAQ - Commodore VZ 3.6 V6 Alloytec 175 $890 - 192kw Bullet performance Performance Flash Tuning | Bullet Performance Racing 190kw - after 187kw? 175 - 170 after? Both with 98ron fuels. Turbo industries...

Anyone done a mail order tune for their vz v6?

Any update, looking at getting one of the turbo industries alloytec tune.

I did a search and most threads are a few years old, just wondering if there are any good alloytec mail order tunes out there now. I've searched the net and seems to be a few incredible ones out there, are there any that can back up there claims? I just picked up my alloytec VZ Berlina...

I just bought some 12mm ones, wish I had of read the previous post first, just have to find time to install and see how it performs. Just put a twin 2.25in cat back exhaust and SS inductions growler kit on this morning, hoping this combination should make it go a bit better.

I sold my supercharged VP Clubsport for $6000 a couple of years ago. All genuine expect the terra charger.

DESCRIPTION: Wanted to Buy alloytech performance parts ITEM: Car is stock so after things like CAI, k+n filter, exhaust/extractors, mace insulators etc... Some ls1's came out with a 2.25in exhaust which I would be willing to buy. LOCATION: QLD, Brisbane Northside. CONDITION...

Thanks for the info, just as I thought, just wondering now if it's worth going the bigger 25mm spacer for a longer runner. 25MM COLD AIR INTAKE MANIFOLD INSULATOR ALLOYTEC VZ-VE - Mace Engineering Group Cheers.

If you have an android phone get the "torque" app and any elm327 adaptor off eBay, there only like $15.