where to mount immobilizer on vh?

[budgieVH]

hey guys i got my alarm system.. i just dont know where a good spot is to mount my immobilizer in my vh commodore..

if you guys have after market alarm systems where did you mount it?

thanks and have a good week end

[strgas]

don't make it to easy to get too , but remember its only going to slow them down and alarms can be easily bypassed , mine was mounted behind the instrument cluster and not visible from the foot well .

[delcowizzid]

i wouldnt even bother going to much effort to hide it they are so easy to start anyway it will make it slightly harder to stop it making a racket but meh

[strgas]

air fuel or spark remove one of the three and the car wont go to far ????

[budgieVH]

i was just thinking in between the front right panel and the plastic interior next to the accelerator pedal. it isn't visible unless you took that plastic bit off but it will be well hiden. the by pass switch i was just going to tuck away in my fuse box..

i was thinking about putting it behind the cluster but to much messing around..

i looked under that plastic bit pf interior above the pedals but not much room or a good spot to mount it.

[budgieVH]

air fuel or spark remove one of the three and the car wont go to far ????

i have a fuel line solinoide rite infront of carbie.. but i have expansive stereo and alot of work done to interior ect lol

[strgas]

mount it under the rear seat . the module isnt the problem its the wiring to and from and as most good car theives no the wiring back to front it wont take long to get around what ever you do . then there is always a tilt tray to worry about ????

[budgieVH]

mount it under the rear seat . the module isnt the problem its the wiring to and from and as most good car theives no the wiring back to front it wont take long to get around what ever you do . then there is always a tilt tray to worry about ????

wiring and thieves isn't my problem just yet.. the system has black wiring. all i asked is for mounting options and opinions lol

[vkberlina]

wiring and thieves isn't my problem just yet.. the system has black wiring. all i asked is for mounting options and opinions lol

it wont matter even if its pink wiring its easy to get around.
It will cut the ignition wire, damn thats hard... alligator clip a wire from the battery to the coil.
Starter motor wire disabled, simple short the starter motor out. easy esp on a holden 6.

So go get yourself a fuel cut off solenoid from a gas conversion place find a real prick of a spot to mount it and wire that up so if they cant get fuel and they can access the solenoid to open the fuel line they had better to geta tow truck or car trailer

Scott

[budgieVH]

i have a fuel cut off line already! question is where to mount alarm...

dont worry about it ill post some where else

[strgas]

mount it under the center console and fit a croc lock to the bonnet

[ari666]

id say mount it behind your radio.

[vkberlina]

i have a fuel cut off line already! question is where to mount alarm...

dont worry about it ill post some where else

mount it under the cash crash pad where the VH/SLE or VK/VL calais hae dash speakers on the RH side of the car, prick of a spot to access unless you remove your crash pad

Used to be a good spot to fit radar detectors

cheers
Scott

[v8commy]

id say mount it behind your radio.

if you could fit it ive got no room behind mine my deck dosent even go all the way in

[budgieVH]

okay...

what i have done.. in the vh commo where the fuse and relay area is i un screwed that part of interior and there was stacks of room behind there... i mounted it rite at the back of the fire wall behind the cluster. bit of a pain but oh well. next week i will have to take it out again to wire up the central locking kit kill start!

[ari666]

if you could fit it ive got no room behind mine my deck dosent even go all the way in

sounds like someone needs a lesson in cable ties and cutting wires to length

[strgas]

sounds like someone needs a lesson in cable ties and cutting wires to length

sounds like another quality strathfeild install ... just jam it in and roll up the extra wires and stuff-em up under the dash

[budgieVH]

sounds like another quality strathfeild install ... just jam it in and roll up the extra wires and stuff-em up under the dash

haha no good... least they dont tape wires together! i have seen that done by auto barn once

[strgas]

hmmmmm taped together one step away from a scotch lock ??? always solder and never have a problem again . Seen a install from there sth melb branch some years ago and they just stripped the wire and pushed it into the back of the ignition switch connector block not even on the acc side ... top marks for that one guys ......

[budgieVH]

hmmmmm taped together one step away from a scotch lock ??? always solder and never have a problem again . Seen a install from there sth melb branch some years ago and they just stripped the wire and pushed it into the back of the ignition switch connector block not even on the acc side ... top marks for that one guys ......

ohh ouch!

i either solder or crimp.. i build laser machines dooing all the electrical stuff and if we did that at work id get in shit and it would endanger other peoples safety haha blew up a 600volt power supply once!