Results 1 to 5 of 5

Thread: inlet manifold gasket leak?

  1. #1
    Ride
    VN-Series I-6-90

    Join Date
    Apr 2006
    Posts
    64

    Question inlet manifold gasket leak?

    Hey peoples, my cars idle is a little bit lumpy, i know i will never be perfect.

    So i had a bit of a looky see and everything looks pretty much as clean as it was after it was all degreased, except round the back of the motor. Behind the throttle body, below the level of the intake manifold there is like a flat at the back of the motor it has freshish looking oil there.

    Just wanted to know if there would be anything else, other then the intake manifold gastket, that could be buggered to get oil there? I just cant see in behind there properly and $220 is a bit of dough to waste un-necessarily.

    ... Just went and had another look around and it also looks like my PCV valve has some oil leaking from around it could this cause any idle problems too?

    Cheers,
    Apoc.

  2. #2
    timgte is offline v8 fuel sucker
    Ride
    Berlina

    Join Date
    Apr 2008
    Posts
    7

    Default

    i just did the same job on my v8. I had a bad idle too and after doing manifold gaskets it runs perfect. On the v8 the dizzy is up the back too which has a gasket that can leak but not sure about the v6

  3. #3
    Ride
    vn calais, vs clubsport #137

    Join Date
    Jun 2005
    Posts
    785

    Default

    v6 runs dfi igniton, no dizzy, could be oil leaking out the bottom of the throttle body, through one of the small hoses.

  4. #4
    alipete's Avatar
    alipete is offline Ban Speed Camera's
    Ride
    VS Executive

    Join Date
    Jul 2005
    Posts
    30

    Default

    V6 are known for leaking oil there it comes from the main oil seal or the valley gasket.

  5. #5
    PaRaDoX's Avatar
    PaRaDoX is offline boosted!
    Ride
    Forester GT, VT S Supercharged, Supra Turbo

    Join Date
    Apr 2005
    Location
    Melbourne, Victoria
    Posts
    3,244

    Default

    just replace the gasket, ALL v6's need replacing

    its the first thing id do to a v6 when getting it...


Similar Threads

  1. inlet manifold
    By ab56452001 in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 16
    Last Post: 03-01-2007, 09:52 PM
  2. new inlet manifold gasket and fuel filter, but now code 45!!!!
    By Fully in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 2
    Last Post: 13-07-2006, 10:37 PM
  3. Inlet manifold-exhaust manifold cracked
    By aussieghostrider in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 1
    Last Post: 22-06-2006, 10:23 PM
  4. inlet manifold
    By madsav in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 5
    Last Post: 16-08-2005, 04:19 PM
  5. changing inlet manifold gasket??
    By muney in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 8
    Last Post: 25-08-2004, 09:17 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72