Button in the glovebox doesn't open the boot, works if someone pushes on the bootlid while the button is pressed... can hear the sound but it doesn't unlatch. Is this just a matter of adjusting in the same way as tightening the manual boot release cable in a VR? (Screws and slider near boot lock, did it in my VR last week) I'd just have a look but my VN bootlid is coated in Dynamat.
The reason I'm asking is that I'd like to remove the external boot lock altogether. As a precaution, is it particularly difficult to set up a manual boot release handle inside the boot like the VYs etc have? In case this problem comes back
Cheers
Sam
WTB: mulberry VN interior parts
I've had that problem since i replaced the boot rubber seal. It still opens, but you have to press it about 3 times in a row, or as you said, put some pressure onto it.
Not sure how to fix it, but i figured my problem was the rubber was too thick, and just needed to mould into place.
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
adjusting the height of the boot can help too. i adjusted mine down so the spoiler would sit in line all round and it became a bit of a pain in the but to open. hot days especially.
you need to adjust the metal bracket that the boot clip sits in once the boot is closed. there is a 14mm nutt i think, slightly undo the bolt and slide the bracket either up or down to adjust it to make your boot open.
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
You can do it with the boot open. Loosen the nut, tap the bracket up a bit, check the button, keep going until it opens.
I'd rather just get the rubber set like the previous one, otherwise my lines wont line up (As Pauls spoiler didn't line up)
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
sorry i wote it wrong (i was refering to what the clip sits in) not that you actually have to do it when its closed lol, that would be fun, but it wouldnt work.
hmm. The more I think about it, the more I want that boot lock gone. It's in an annoying place, like a Holden badge, but worse.. The car will look so much smoother without it.
OMG I WANT A GREY VN SS
lol oops that just came out by itselfwhat do you reckon a VN SS 3 piece spoiler would look like with my bodykit?? all in white, obviously... serious question
WTB: mulberry VN interior parts
i think it needs something smoother, like an aero spoiler.
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
Get a flip down number plate bracket and put the key hole behind that. I've seen it done on an XB Falcon, looks good.
hmmm, nah I like the clean look and I don't mind if it takes 2 people to open the boot, I think I'll just remove that lock altogether. Good idea though
And stealthy, I'm not really a fan of the stand apart spoilers (for lack of a better phrase), I love the moulded look. The SS or Group A are my only options really, but I think the Group A one would look ridiculously too big. Maybe.
haha I don't know what I think.. and with spoilers it's not like you can just try them on .. at least not with a 3 piece!!
WTB: mulberry VN interior parts
Get 3 mates then? lol
Just get an International (Caprice) bootlip then. Think T roy is selling his
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
101_2916.jpg - Image - Photobucket - Video and Image Hosting
hmm.. it fits your car very well but I'm not sure if I want one ... I'm too picky![]()
WTB: mulberry VN interior parts
oi if you take your lock out sammy b send it my way! mine got destroyed when the pricks broke in...i'd love a new one :P
and has anyone EVER seen the VP holden lion badges for the bonnet and boot anywhere new? i've got new ones of every other badge...
haha ok mate, will do. You should get one of those VN Calais HBD option badges, the standup ones. That'd look right at home on your car. Get rid of the lion badge and slap one of those on there
How's things anyway dude? haven't spoken for ages :'(
WTB: mulberry VN interior parts
-------------------------------------------------------------------------------------------
* * [] [VP CALAIS INTERNATIONAL] [EFI 304] [T56] [] * *
* * [] [VP BERLINA LX WAGON] [EFI 304] [T5] [] * *
-------------------------------------------------------------------------------------------
STEALTHY's Shed Clean Out! Buy my ****
Originally Posted by davway
Originally Posted by JONNNNOOOOO!!
hahaha as if it did ... did it?![]()
WTB: mulberry VN interior parts