bumpers

[MAC-VN]

sorry about making a thread but cldnt find it anywere
how on gods earth do u take the bumpers off a vn
dnt they bolt off or something

[MAC-VN]

can someone fkn help i need them off in next 20 mins

[Pub247]

yeah theyre bolted on from the boot for the rear one and the front needs reo taken off with it i think. there will likely be some screws aswell aroun the wheel well

[MAC-VN]

were in the boot

[MAC-VN]

and therre like to lil pot reverts in the wheel well above were swrews were

[R0d]

and therre like to lil pot reverts in the wheel well above were swrews were

lol someone pop riveted the bumper on? haha. on my mates there was a couple bolts under the bumper in the middle think a couple on inside boot and screw one the sides but sides also are on like a slider, cant really remember much tho

[Pub247]

yeah thats about right look under capert id you got it

[MAC-VN]

i got the carpet out
so werre are these bolts
the pot reverts are in the wheel well on the lip of the bumper up really high near the coner is tht holding to the car or what how can i get thm out with are a pot gun

[R0d]

i got the carpet out
so werre are these bolts
the pot reverts are in the wheel well on the lip of the bumper up really high near the coner is tht holding to the car or what how can i get thm out with are a pot gun

dont know what the pop rivets are there for, but there were none on my mates. There bolts are on the inside should be near where the boot latch catches on the beaver panel, might be some on bumper ends on inside 1/4 panels but not sure, shouldnt be hard to take a bumper off mate. Just pull on parts on bumper to see where its being held on by and find the bolts

[MAC-VN]

ok guys how i get a pot revert out without a pot gun

[H1GHROLLR]

you dont use a rivit gun to take them out thats only for putting them in you have to drill them out

[MAC-VN]

ok thats what i thought
do i get a small drill pieace drill hole then put screw in then pull out oii explain please

[Vt-Brrrlina]

get a drill that is same size as the head of the pop rivet and drill slowly - itll just take the head off then and slide out easily

[MAC-VN]

I GOT IT OFF GUYS i didnt need take pots out thanks all uses for tht i undone the poot bolts n slid it off cheers thanks guys hope the front is the same

[social]

hahaha...omg this kid is classic lol, fun times ahead forsure...

[Pub247]

but thats what we're here for to help people who dont know squat about cars

[MAC-VN]

PUB WHAT U ON ABOUT I CAN SQUAT ON MY CAR UR WRONGGG WRONGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG

[hemi01]

Hey MAC,

The first thing that I would normally recommend before starting a DIY job on a car would be to obtain a workshop manual and research the required job.

But in your case that would be a waste of time because after reading your posts, I doubt that you can read.

At least it was just the bumpers you were attempting to remove and not the cylinder heads.

Here's hoping that that's the end of your 'do it yourself' repairs. For the sake of the safety of you, your passengers and the public at large.

[MAC-VN]

hemi mate im new to cars iight the reason i asked is so i cld do it the right way
so take ur bullshit n stick it mate

[ibs87]

ease up turbo...!!!lol.. wat u did was the right thing. Not everyone has the time to research how to do the job. Sometimes u have to do it then n there..if u dont have a manual..forums are the next best thing.

[MAC-VN]

thanks ibs this forum is good cos there alot of good ppl
im just rying to learn all i can i may not no to much but atleast i anit like a try hard car guy who only wants to help him self n really nos shit all
so thanks guys

[Bz Kn33z]

Get a car Manual, it will help alot, there is heaps of information in there even the smallest things, good to know you got the bumpers off , sometimes you just have to be self taught.