Results 1 to 5 of 5

Thread: Stato rear courtesy light into exec

  1. #1
    Ride
    93' Pov-Pac

    Join Date
    Jul 2010
    Location
    Vic
    Posts
    215

    Default Stato rear courtesy light into exec

    I'm trying to figure out how to wire up the stato rear courtesy lights (where the grab handles are) in a Exec with a low series BCM.

    It looks like the power source can just be taken from the front courtesy light, but there are another 2 wires which need to be accounted for, I believe one of them is just an earth to the body. How about the other wire? Factory wiring diagram shows it to be wired back to the BCM (could even splice it in with the wire running from the keylight to the BCM)

    Is there an alternative/easier way to wire it up, or should I be trying to match it as closely to the factory wiring diagram as possible?

  2. #2
    Ride
    VS

    Join Date
    Jul 2010
    Location
    Sunshine Coast, Queensland
    Posts
    1,051

    Default

    Wire them to your door light switches, one to direct power and one to ground. This will mean you have the option for off, on or on when door opens.

  3. #3
    Ride
    93' Pov-Pac

    Join Date
    Jul 2010
    Location
    Vic
    Posts
    215

  4. #4
    Ride
    VS

    Join Date
    Feb 2011
    Location
    Newcastle
    Posts
    19

    Default

    In my last Commodore i had, i connected them to the 2 wires on the interior light. Found it easy enough to do and they come on when any door was open and still had the over ride switch as well.

  5. #5
    Ride
    93' Pov-Pac

    Join Date
    Jul 2010
    Location
    Vic
    Posts
    215

    Default

    Bit of a bump, I finally got around to wiring the Statesman Rear grab handles up.

    I connected the orange/black wire pf the rear map light to the positive wire of the dome light loom (spliced in), and did the same for the black wire to the negative wire of the dome light loom (also spliced in). That only got the lights working when the dome light was on (when a door is opened, or if the dome light is switched on manually)

    There is another wire on the rear map lights, which are white in a VQ, and white/green in a VR/VS, you want to extend these wires, join them together at some point, then run the end of the single wire to a constant earth. I chose a screw hole for the dome light housing (Pick a different hole to the one where the front map lights earth to)

    So now the rear map/courtesy lights come on when the dome light is activated, and can be switched on independently too.

    If you want me to explain anything in further detail, let me know.


Similar Threads

  1. [VR-VS] Adding a switch to courtesy light.
    By hako in forum Holden Commodore How-To's
    Replies: 4
    Last Post: 05-12-2010, 07:03 PM
  2. courtesy light wire for footwell lights.
    By jasnos in forum Electrical Wiring / Questions
    Replies: 13
    Last Post: 26-08-2010, 07:12 PM
  3. door courtesy light cover
    By jafo in forum General
    Replies: 4
    Last Post: 09-06-2009, 08:33 PM
  4. Installing rear reading/courtesy lights into a VR Exec
    By whitey1977 in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 0
    Last Post: 16-06-2008, 02:24 AM
  5. VR/VS owners : You can install interior rear light like in berlina/Calais/Stato
    By Damo83 in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 4
    Last Post: 05-01-2007, 08:20 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72