Anyone know where to get 8 bolt vp-vs Flywheel?

[hillboy89]

Hi there i recently clean swapped my manual vn with a auto vs... the vn had the series two motor with the 8-bolt fly wheel i have another full manual conversion here just without the fly wheel and have discovered that finding another 8-bolt flywheel has proved difficult.. Has anyone found a good supplier or got one to swap?? Got many VN-VS parts.

Also just to double make sure the 8-bolt fly wheel does fit a vs? and the bell housings are the same? i only sure they fit up to a vr wasnt sure about the ectotecs.

Thanks

[dufus]

wrecker is your best bet

[VrWagz1]

Maybe email CRS to see if they make them. Besides that and ebay.

Just found this cruising the forums

Just spoke to tom he ranf CRS and they said $600 for flywheel
I have a feeling he may have asked for the custom 6 bolt one as its listed clearly on their website as FW41N new 8 bolt flywheel v6 commodore $308 I will have to ring them myself tomorrow with part no and check it out

Haydz once again thanks your been a tremendous help

[hillboy89]

have tried all wreckers within 500ks... And cant find anything on ebay they are all 6 bolters..

But yeah thanks Wagz i will have a look at CRS willing to pay that price.

EDIT:

$580 without the postage... think ill keep looking

[social]

you could basically go into youpullit, find a manual vp / vr or vs and take the flywheel out of that and there you go, they are the easiest flywheel to come across below vs, only problem as said above are the 6 bolt ones out of the vn series 1s

[VrWagz1]

Only problem with that is most wreckers iv seen wont sell a fly wheel or g/box or even a center console plate. They sell them all as a whole packaged manual conversion and wont separate.

[social]

over here in SA, theres a place called UPullIt its probably biggewst wrecker in SA, you go in, tear apart a car, get wat u want carry it to the desk and pay for it, if some lowlifes in other wreckers in diff states dnt wana sell yuo just the flywheel tell them to sit on it, im sure someone over here in SA could find you a flywheel, buy it and u pay em back + postage.

[VrWagz1]

the pickapart i went to here tried to jack me $330 for a L3 cluster and $100 for a flogged out set of rear control arms for my wagon, obviously i told em to keep them. The wreckers here get a hold of anything V8 or manual and next minute its got prices on it you only find in jewlery stores

[POVRTY]

the pickapart i went to here tried to jack me $330 for a L3 cluster and $100 for a flogged out set of rear control arms for my wagon, obviously i told em to keep them. The wreckers here get a hold of anything V8 or manual and next minute its got prices on it you only find in jewlery stores

bah!!!!!!! we have the same problem every one u speak too referes to our wreckers as gold finger.......1 guess why.

[hillboy89]

yeh SA is bit far from me...

something finally showed up on ebay.. he got it advertised from a vs - vy.. its a 8bolt but i thought only vp-vs were the same???

VS VT VX VU VY V6 / Supercharged V6 Flywheel & Clutch - eBay Other Transmission, Transmission, Car Parts, Accessories, Cars, Bikes, Boats. (end time 22-Feb-09 23:03:22 AEDST)

if anyone can help me?

its was hooked up to a getrag

[Zuicider]

wouldnt think the flywheel really matters
its a hydralic clutch set up and its been in a fire

[VrWagz1]

Its off an ecotec so it'll fit it. But its for a getrag box by the looks of it and they ran a different flywheel to the T5's

[deanos70]

Mate i found one the other week using find a part, you reach heaps of wreckers with it , i got it for $275 plus postage
try this link below, crs do sell the billet flywheels to suit the ecotec 8 bolt for about $650 or so , but you need to get them balanced

http://www.findapart.com.au/