Results 1 to 4 of 4

Thread: VX Calais fan not working - I've searched

  1. #1
    VSB
    VSB is offline
    Ride
    VX Supercharged Calais and Vr Berlina

    Join Date
    Mar 2005
    Posts
    32

    Default VX Calais fan not working - I've searched

    My Calais climate controls kicked the bucket, fans not working on any speed, I've checked the fuse, blower motor which works when I pulled it out, and swapped relays over but no go,

    The only way I can get the fan to go is bridge the relay, Which is where I'm stuck where does the signal go once it leaves the climate control module?

    I've checked the connections at the back of the module and all seem good,

    I couldn't find the resistor that can play up, but I'm told that the fan will only work when in high which it doesn't,

    Any help would be appreaciated

  2. #2
    Calaber's Avatar
    Calaber is offline Nil Bastardo Carborundum
    Ride
    CG Captiva SX

    Join Date
    Nov 2007
    Location
    Lower Hunter Region NSW
    Posts
    2,434

    Default

    VSB

    I just fixed my air con in my VY yesterday by replacing the amplifier (or resistor if you prefer). I was able to replace the amplifier very easily, but it may not be in the same location on your VX.

    In my VY, it is located immediately above and to the right of the blower fan. The fan wiring leads directly from the blower motor, through a small connector with a 35 amp fuse, into the amplifier. I don't know what ithe amplifier looks like on the VX or where it is located, but it is a white plastic plate, with a wiring connector, retained by two self tappers. It is much easier to locate if the glove box lid and upper cover is removed from the passengers foot well. It cost just over $80 trade (but again, this is for a VY). When I removed the old one, it had a soldered joint that had unsoldered itself.

    Your Calais will require a different amplifier as it is dual zone, and you will need your VIN to ensure you get the right part.

  3. #3
    VSB
    VSB is offline
    Ride
    VX Supercharged Calais and Vr Berlina

    Join Date
    Mar 2005
    Posts
    32

    Default

    Hi Calaber,

    Thanks for the reply, I found the resistor circuit and heatsink, pain in the but to get out unless you remove the glovebox, I cleaned up the circuit board and resoldered all the points and it's a goer.

    VSB

  4. #4
    Calaber's Avatar
    Calaber is offline Nil Bastardo Carborundum
    Ride
    CG Captiva SX

    Join Date
    Nov 2007
    Location
    Lower Hunter Region NSW
    Posts
    2,434

    Default

    Quote Originally Posted by VSB View Post
    Hi Calaber,

    Thanks for the reply, I found the resistor circuit and heatsink, pain in the but to get out unless you remove the glovebox, I cleaned up the circuit board and resoldered all the points and it's a goer.

    VSB
    That's good mate. Glad you're all fixed now.


Similar Threads

  1. tacho not working! i have searched!
    By SLO 057 in forum Electrical Wiring / Questions
    Replies: 1
    Last Post: 06-02-2009, 04:47 PM
  2. Replies: 9
    Last Post: 30-12-2006, 11:06 PM
  3. Already Searched Zorst Wont Fit
    By juice in forum VN - VP Holden Commodore (1988 - 1993)
    Replies: 6
    Last Post: 30-07-2006, 05:15 PM
  4. good mechanic (already searched)
    By ssmate in forum VR - VS Holden Commodore (1993 - 1997)
    Replies: 0
    Last Post: 29-07-2006, 04:17 PM
  5. from 3l to v8 conversion help (searched)
    By ROTA_MOTION in forum VL Holden Commodore (1986 - 1988)
    Replies: 1
    Last Post: 25-10-2004, 10:37 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72