VZ alloytec codes

[burnz]

P0008 - Engine Position Performance Bank 1

P0009 - Engine Position Performance Bank 2

P0016 - Crankshaft / Intake Camshaft Position Not Plausible Bank 1

P0017 - Crankshaft / Exhaust Camshaft Position Not Plausible Bank 1

P0018 - Crankshaft / Intake Camshaft Position Not Plausible Bank 2

P0019 - Crankshaft / Exhaust Camshaft Position Not Plausible Bank 2

P0112 - Intake Air Temperature Sensor Circuit Low Voltage

P0113 - Intake Air Temperature Sensor Circuit High Voltage

P0117 - Engine Coolant Temperature Sensor Low Voltage

P0118 - Engine Coolant Temperature Sensor High Voltage

P0125 - Insufficient Engine Coolant Temperature for Closed Loop Fuel Control

P0196 - Engine Oil Temperature Sensor Circuit Range / Performance

P0197 - Engine Oil Temperature Sensor Low Voltage

P0198 - Engine Oil Temperature Sensor High Voltage

P0261 - Fuel Injector #1 Short to Ground

P0262 - Fuel Injector #1 Short to Power

P0264 - Fuel Injector #2 Short to Ground

P0265 - Fuel Injector #2 Short to Power

P0267 - Fuel Injector #3 Short to Ground

P0268 - Fuel Injector #3 Short to Power

P0270 - Fuel Injector #4 Short to Ground

PO271 - Fuel Injector #4 Short to Power

PO273 - Fuel Injector #5 Short to Ground

PO274 - Fuel Injector #5 Short to Power

PO276 - Fuel Injector #6 Short to Ground

PO277 - Fuel Injector #6 Short to Power

PO327 - Knock Sensor Bank 1 Circuit low Frequency

PO328 - Knock Sensor Bank 1 Circuit High

PO332 - Knock Sensor Bank :2 Circuit low Frequency

PO333 - Knock Sensor Bank 2 Circuit High Frequency

PO335 - Crankshaft Position Sensor Circuit

PO336 - Crankshaft Position Sensor Signal Range / Performance

PO337 - Crankshaft Position Sensor Circuit low Duty Cycle

PO338 - Crankshaft Position Sensor Circuit High Duty Cycle

PO341 - Camshaft Position Sensor Malfunction

PO342 - Camshaft Position Sensor Voltage low

PO343 - Camshaft Position Sensor Malfunction

PO346 - Camshaft Position Sensor Malfunction

PO347 - Camshaft Position Sensor Voltage low

PO348 - Camshaft Position Sensor Malfunction

PO366 - Camshaft Position Sensor Malfunction

PO367 - Camshaft Position Sensor Voltage low

PO368 - Camshaft Position Sensor Malfunction

PO391 - Camshaft Position Sensor Malfunction

PO392 - Camshaft Position Sensor Voltage Low

PO393 - Camshaft Position Sensor Malfunction

PO443 - Canister Purge Solenoid Circuit Malfunction

PO458 - Canister Purge Solenoid Circuit Low Voltage

PO459 - Canister Purge Solenoid Circuit High Voltage

P0504 - Brake Switch Circuit Malfunction

P0521 - Engine Oil Pressure Sensor Circuit Range /Performance

P0522 - Engine Oil Pressure Sensor Circuit Low Voltage

P0523 - Engine Oil Pressure Sensor Circuit High Voltage

P0560 - ECM Battery Supply Voltage Out of Range

P0562 - ECM Battery Supply Voltage <11 Volts for 5 Seconds

P0563 - ECM Battery Supply Voltage >16 Volts

P0615 - Starter Relay Control Circuit Faulty

P0616 - Starter Relay Control Circuit High Voltage

P0617 - Starter Relay Control Circuit Low Voltage

P0625 - Generator F Terminal Low Voltage

P0626 - Generator F Terminal High Voltage

P0627 - Fuel Pump Relay Malfunction

P0628 - Fuel Pump Relay Malfunction

P0629 - Fuel Pump Relay Malfunction

P0685 - Main (Engine Control) Relay Malfunction

P0686 - Main (Engine Control) Relay Circuit Low Voltage

P0687 - Main (Engine Control) Relay Circuit High Voltage

P1258 - Engine Coolant Over-temperature Protection Mode Active

P1668 - Generator L Terminal Circuit Malfunction

P2105 - ECM Voltage Supply Incorrect

P2227 - Barometric Air Pressure Sensor Range / Performance

P2228 - Barometric Air Pressure Sensor Low Voltage

P2229 - Barometric Air Pressure Sensor High Voltage

P2251 - Oxygen Sensor Signal Changes >10Mv as Heater Control Switches

P2254 - Oxygen Sensor Signal Changes >10Mv as Heater Control Switches

P2500 - Generator L Terminal Circuit Low Voltage

P2501 - Generator L Terminal Circuit High Voltage

[VZ SV6]

Thanks very much for posting these. Where did you get them from?

[burnz]

Thanks very much for posting these. Where did you get them from?

i'd rather not say.

[Torquative]

trial and error aye Chris

[burnz]

trial and error aye Chris

well since i'm semi retired LOL.
i got a lot of softwear from my last employer (nothin illegal).
and as well as my own cnc softwear which is licenced to me.

[Torquative]

i wouldve went for the "stuck paperclips in various holes and worked out what blew from there" but what you said sounds just as good

[mas996]

sweet, so what are these for? lol

just if your lcd show these codes you know what it is?

[impulsesv6]

25 pages of codes here... been on the net for yrs

need tech 2 or alike to read the codes