Search results

No idea, look like standard bearing to me, picture attached. Small bearing says NMB Thailand, nothing else.

I've put new bearings in, much quieter! Only difficult bit was getting the over run pulley off, need impact which I did not have. For the next person! Small sealed bearing is a 8mmx23mmx14mm ABC bearings number B8-85T12DDNC Large sealed bearing is a 17mmx47mmx14mm ABC bearings number 63032RSC3

Hi forum, I purchased a replacement lower grille for my 2016 SSV vf2, it's bare plastic, hence need painting. Ebay say 'W690F PHANTOM BLACK' paint store could not find this code and there are many variations of this colour. Does anyone know; What the paint code is? Is the standard colour...

Thanks, the video makes it look easy! Looks like I need to pull the bearings out to get the numbers and go to the bearing shop!

I need to place the alternator bearings in my 2013 SSV VF1 LS2 (165,000 kms), it's a Mitsubishi 140A , numbers 92254 672, A002TX3781, I would appreciate it someone can advise the bearing numbers so I have them prior to pulling the alternator apart. Thanks.

UPDATE - working perfectly (when using same pins as sketch). Changed signal out D3 to D9, changed switch from D5 to D7 and now works perfectly. Stooge, thanks, you put me on the right track. I’m a novice with Arduino, D3 is also an interrupt pin, pin5 is also a PWM, either the square was...

I checked the pull resister on pin 3, it's working correctly, measures 4.5v and drops when button pushed. However, I did not consider the reset on pin 3, it does make some sense that could cause the issue, I will change it and let you know. Thanks for the pointers.

Hi Guys, I built the controller with the Nano board, it works great with engine off, ignition on. With engine running, the switch works normally, however the valves change state randomly (even with switch disconnected) every 20s to 4 minutes. Has anyone else had this issue? The mufflers I...

Hi Guys, I want to give this a go, is the HSV electrical bimodal motor & butter flys the same as VF2? thxs

Has anyone purchased the Xforce e2-vf82-bim-kit it the one that uses the stock bimodal muffler? Is it decent quality and does it fit well? How quiet in quiet mode compared to stock? Open, what's the base like?

VF S1 ss, with OTR. On the bottom of the radiator (outlet pipe) there is an extension of plastic pipe that has an orange o'ring, mine has a leak. Can you get just the o'ring, if so, what the size of it? Or is it buy the whole extension piece from Holden? FYI - the bottom hose clamp has rubbed...

My 2013 redline sedan, 145000 km. Went King SL with Monroe gas. Amassing difference in body roll. But, SL should be 380mm rear and 375mm front. But ended up with r 355 and f 365 after 2 weeks. 2/3 full tank and empty car. Too low in rear. Told it is because of Bush sag. Have new front strut...

Does anyone know where to get the windscreen 12mm seal for the front & back windows? Holden don't have a separate part for it as it come with the screens. I have removed it to paint the car.

I have a 2013 S1 sedan, SSV Redline, does anyone know what the sensor in the boot is & does? It's on the floor, up against the fold down centre section with foam around it, size 1cm wide & 4cm long.

Thank you for the article, I have my head round it now. I assume best to access the fill plug once exhaust is cool!

I've read lots on this, I have done 140K km and time to change the fluid, my question is, what is the easy way to get the fluid back in the transmission? I was thinking to pump through a hose connector that screws in to the drain plug then follow the level check, then remove the connector. If...

They work great. car stops! Only issue, if wheel weights are inline with the the round bits on the pads they hit. I removed the small wheel weight, wheels are standard 19" redline wheels. No Squeal but use used anti squeal, I found the HD pad squeal more than the ults. The ults definitely have...

thanks, so much for that idea!

Hi Alex05, did you find out whether a VE door will fit a VF?

update - I've had the rack replaced under warranty, had to push a little though, happy days. :)

Thanks, it is booked in for next week, we shall see what happens!

Hi, I’ve read the older posts on the “service steering column lock” and most are that the car will not start, or similar to my issue but in 2014. I did see there is a recall in the USA for this issue. Mine happens while driving and you lose the power steering while moving. Restart the car at...

On a SSV RL series 2 (wagon standard height), has anyone run this set up and if so have photos? Why I hear you ask, I get the concave look in the rims F & R and can rotate the tyres. But I am worried the stretch is too aggressive! Will the rim be outside the guard with the 35mm offset F &...

Is there Aux power that turns on & off with the ignition on the boot fuse panel? I checked the radio (f5) and rear entertainment (f14) fuses and they are constantly 12v with ignition on & off (accessories off as radio was powered off). I am installing a Black Vue dash cam with park mode!

Fergie submitted a new Showcase Item: 2010 Holden Commodore sv6 Read more about this showcase item here...

Fergie submitted a new Showcase Item: 2013 Holden Ss-v redline Read more about this showcase item here...

I'm thinking of the 330kW option for my 2013 SSV, I have an auto and I thought the auto was 10kW less than the manual because of the auto capability, does the extra power create any problems, like destroying the transmission?

Does anyone know where and which one is the VSS wire in a VE series 1 SV6? I want to wire a Head Up Display without the GPS so it works in tunnels. Thanks