Search results

Bringing up an old post, just pulled out and replaced some well and truly stuffed front shocks, purchased strut mount and bearings , new bump stops, now all in but top of strut is moving when turning and making a rubbing like sound. With the bump stop is it supposed to be free floating or placed...

Re 2010 wagon This seems to be best spot to post my message as relevant . Obviously age of these cars things will happen, have had to replace front wiper motor as nylon teeth were gone now My rear wiper /washer not working but yesterday with ignition on and wiper switch pushed forward when I...

After another midnight wake up had a go. Thank you, I have done this, when I did it first time alarm went off immediately, so got another wire to make sure had good contact so far so good, will now wait and see. Now to work out why rear wiper isn’t working. Will find suitable post for it.

Another Horn alarm randomly going off. Hi everyone , have been reading this post , before I do the wire twist, just wondering since I have replaced my damaged door on a ve wagon with a ve Ute door is the harness same, all locks and windows working , I changed lock with my original one so key...

furthrr to this, she did replace the engine at a cost of 10k.

My sisters LLT had the timing chain issue but one the the Cats was also completely blocked which was causing an exhaust sensor error, this was kicked up as no heat coming from tail pipe and then put heat sensor in cat amd it was hit.

Hey I have a 2010 LLT engine that had the timing chain issue, I was considering putting this into my omega to replace the 3.0 but believe can’t be done, has there been a work around this yet. I understand it’s the bcm that is the issue. Can the 3.6 block be used or is it all the timing issue...

Also adding to this I have no dash lights

Today I unplugged harness below the left fuse box, now my central locking is not working with remote, do I need to reset anything, all fuses are good, was working fine until now. Central licking works fine except with remote.

Have read through this post, can this be used for Dashcams requiring park mode, so need constant power.

I know this is a old post but I won’t to hardwire my BlackVue dashcam 1ch. Happy just to use the fuse adapter, I’m pretty sure can plug into door for Accessory, which would I use for power, earth well that’s self explanatory.

Had this happen to mine recently, I went into the service mode was putting out 17 v at battery, new alternator put in , still didn’t fix brake light issue though but found the left brake/light element touching and causing a short, easy fix.

Just wondering when setting timing marks and chain what piston should be tdc?

Not sure if this helps, but when I purchased my belt for 3.0 Repco had to ring golden with chassis number to confirm belt as come with 2 different sizes. The belt I got was Serpentine Belt 6PK2125RB.

I’ve read this whole post, what was outcome. I’m just trying to work a way to fit a 3.6 llt engine into my omega. I’m aware of computer needing to change but on the 3.6 itself, what could be changed from 3.0 to the 3.6 so computer could work. There must be sensors that could work it out. Cam...

Haven’t done yet, I’m just playing around, had metal in the engine, it was my sisters.

I did the same and asked Cloys timing if it’s an issue. My cas. It so bad as only an engine playing with. Got this reply. Hope it helps

Yes I’ll attach, I thought I did with post

Has anyone seen this before, explains alot. Decided to strip down my sisters 2010 3.6 engine that was removed from her wagon. There was fragments of metal on cam sensors. Timing chain loose drivers side, rest looks good. Has anyone seen a broken oil filter housing like this. I’m going to rebuild...

Revhigh, So I’ve pulled timing gear off without setting marks, I next want to remove cams as had metal on cam sensors so just searching for issue. Without knowing timing marks is this a major issue or can timing still be set later?

Hey guys, first post but following for some time. My sister had her 2011 3.6 replaced due to timing timing issues and metal on crank sensors. I now have this engine 1- should I strip down and rebuild possibly requiring bearings and timing gear. One of the guides was also broken. Could I sell...