Search results

So after puting the fresh engine in it idled & ran fine (nothing over 4k rpm). Booked in to hi torque today for mild touch up tune (hot as #### day) managed 285kw@wheels 650nm nice even arc, with only 80ks on the engine.. happy dayz Big bump for hi torque! Everywhere in brissie i rang wanted...

Anyone know if vz thermo fans are same for v8 & v6?? Cheerz

All sorted, my bad lol there was a plug on the opposite side of car near ac condensor thing that wasnt pluged in woops... pluged it in & all go,, may have been signaling ( 'no gas in system or something??) Cheers

Is there a fuse for the ac ?? Found tge relay but cant see any fuse.. Issue is no power coming out of wires to ac.. (compressor not kicking in) Purposely did not disassemble the ac unit when done engine swap so i didnt have to regas (was working fine cold as).. now compressor not kicking in &...

So the above pic is how i have set it up, rear out lets t peiced into 'baffled' sealed catch can-then into manifold,,, Fresh air intake from front rocker vent (yet to b plumed into otr) should i get a pcv valve & place it between cc & intake? To govern flow a bit, seems to b alot of air pullin...

Yeah cheers i understand the corect way it should run, just trying to get it 'safely runing' till it gets to to shop.. So if i use this setup since i no longer have a valley vent tube it should b fine?. Run both rear rocker cover outlets to t peice then into sealed catch can, then catch can...

Hi, so got a bit of a mix n match going on.. & just wanna know is runing air breathers of each rocker cover gona get me bye till it goes in for tune & pcv plumbing or do these engines definatly need manifold vac to run safely.? Vz ss ls1 (elec throttle body) 1. New rebuilt engine doesnt have a...

Mine just droped a rod after 2 weeks of owning it!!!.. 130k,s cammed. Searched around & found a Rebuilt cammed long motor was 5k exchange. Second hand ls1 1.5-3k

Just fited up a hd clutch kit with upgraded cushion button/ceramic style disc & noticed the inside diameter of the disk is overhanging the pressure plate bye a few mm! Surely this would cause issues? I rang one clutch mob they reckon b fine will just create a groove there as it wears. Yet to...

So im absolutly strugling to hold the engine down with crane & wedged flywheel bolts to ground .. balancer went on nice & smooth, is it gona b easyer to torque it once back in the car in gear & foot on brake?? Without stressin gbox.

Legend... thanks mate

Hi been thru a few posts, but chasing comformation as i dont wanna stuff it up.. New camed ls1 engine, t56 6speed. (Torque specs) Hd Flywheel/ clutch Hamonic balancer old bolt (then new) Manifold Water pump Cheers for any help, hopefully have the new engine in this w,end then off for a...

O.k, so i have a freshly rebuilt engine with comp 232/234 595lift, rocker upgrade,psi springs etc etc ready to drop in.... Old engine had a mid 220/223 cam, all the bolt ons mafless tuned,,, Will i get away with just a tune touch up & dyno.. or will it possibly need a full retune?? Just...

Looking at pulling my engine for more mods, ecu is tuned for cam/zorst/intake etc.. If i put a stock engine in meantime would i be fine not changing tune?

Watching post, my vz ss fuel guage does the same erratic from half to low fuel alarm goes off... sedan manual

Original mods were done bye walkinshaw so doesnt surprise me they used standard cats, probly for warranty sake or some #hit.. Just bolted up a new xforce twin 2.5" in tonight so will get high flow cats fited after i empty the money bags on new clutch

O.k, thanks for help peoples.. geting clutch done next week will get seal done at same time if there confident at doing the mark it & change trick... cheers

Hi, what i would normally think is a pinion seal leak,,,, but theres no oil leaking around the seal/ input shaft & runing down the diff where they normally do?? The tailshaft coupling has oil all around the bolt holes? Just checking these vz couplings arent oild filled or something lol.. Also...

Hi new to the forum. Picked up this tidy vz ss recently 130,000ks, was hard to find a clean one. Not a single mark or tear on interior. Factory fe2 suspension 19" rims painted in metallic silver Super dark tinted windows Dash guages. 6speed manual, hd clutch billet flywheel (needs replaceing)...

Hi peoples, new to the forum will upload a bit on my cars once i figure out downsizeing pics lol.. Seen a few older posts but seeing if anyone can recommend a place in brisbane southside for a reasonable priced heavy duty clutch fitted plz.. Vz ss ( usual mods cam, etc) 370hp@wheels Allready...