Search results

No didn't adjust the accelerator cable. I will do that and then the shift cable. Thanks for the info

Hi my auto only revs to about 4500 in first then shifts to second. Its at about 50kmh. The kickdown is correctly adjusted. Any ideas? Thanks

There is a few on Ebay

Hi Can anyone tell me the colour name or code for the VP SS wheels? Thanks

Thank You

Thank You

Hi my VP V8 center bearing is shagged and I want to fit a spare tailshaft while I fix mine. I was told it was from a VN V8 auto. The only thing i have noticed is that the rear section shaft is longer on the VN but total length is the same. The rear uni section is shorter on the VN one as per...

Thanks mate for the info

Not sure if its the correct name but how do you remove it? Thanks Sorry just realised should of posted this in my other thread.

Wow too scared to remove it now. Don't know whats underneath. But that can still be repaired?

Thanks mate appreciate the info

Mine does the same but only when hot. Dosen't make a sound when cold or short drives.

Hi can you just remove the rubber only around the rear windscreen ? Or do you have to remove the glass as well? I have one small rust spot that is close to the rubber so want to repair it. Cheers

Thanks guys for all your input and suggestions. Much appreciated.

Tried that just makes it shift harder.

Hi my auto shifts from 1st to 2nd at 4800rpm under hard acceleration. Is that normal as I thought it should rev to at least 5500? If I do manual change it goes to 5800 no problem. Any ideas? Thanks

You could be right as i did have Fe2 and changed to the King Springs it dropped the front another 15mm or so. Funny thing is it never did it for a few weeks so that could be the springs have settled which is causing the noise?

I have a strange knock from the front suspension when reversing and turning wheel to the left or right. When i drive forward it makes the same noise again. Wont do it any other time. No noises at all over bumps etc. I just recently put in new springs, shocks and strut tops. ( I already had FE2...

Thanks guys for the replies. Can I knock out the old hubs and change to the VR ones without removing the arms? I know it will stuff the bearings so can you change these as well without removing the arms? Thanks

Hi, Anyone used AF Racing hub centric wheel spacers? Are they strong enough for street use? I know they are illegal but i have a VP IRS with the crappy offset. Thanks

Can anyone tell what length middle muffler will fit VP IRS? I know the Redback 2.5 is is about 13" long. I'm looking at 14" ones. Thanks

You are right they did make an LE in the VN

I had an LX but never heard of a LE. Must look it up.

Hi not sure if new problem. Never noticed it before but i was going to do the VR VS hub upgrade and decided to check all measurements before i did it. That's when i noticed it was out.

Hi yes it is level ground. I will measure the height and check.

I had to put a few different size o rings on mine until it stopped leaking. I use a slightly over size one.

I had a VP Berlina LX. Mine had the thinner looking stalk. Also mine came with a standard black steering wheel and black steering column. It come with Calais wheels as well.

Hi my VP IRS has the drivers side wheel closer to the outer guard than the passenger side. If i measure it the drivers side sticks out 10mm more. Is this normal or is my cradle out of alignment? Thanks

Hi can any one tell me the difference? Thanks

I'm changed the color of my VP to Anthracite Grey. I had the paint mixed up from a panel shop suppliers. It seems to have a purple tinge to the colour when viewed from a certain angle otherwise looks like a dark grey. Is it right or mixed incorrectly. I have seen a VP international and in this...

Thanks markovr appreciate it very much.

Hi i have a problem with my VP exec with factory alarm. I want to fit an aftermarket alarm and it has wires to use on existing factory alarm arm/disarm. I need to know which are the arm/disarm wires and were they are located. My security disable lock in the pillar has had the wires removed and...

Hi will a VS rear door fit a VP? Cheers

NP just heard that a lot of people they say are a better head. Will just get a VP-VS set then.

How can i tell if the heads i look at to buy are VN and not VP-VT? Cheers

Sorry mate should of given more info my bad. Is this what you mean?

This is how mine is but i added new rotors. These are just old ones to test the setup. I also had to use adaptors as my brake lines are the old inverted type not the new double VT ones.

Hi i have done the VT front brake upgrade and works ok. My question is how and what is the best way to adapt the VS booster and VT master cylinder to my ABS? I cant seem to find a lot of info and all the VT masters i have seen have 3 ports and my old one only has 2. Cheers

Thanks for the all the replies. I only do manual up shift sometimes anyway.

But will shifting manually damage the auto is what i should of put in my post.