Search results

haltech e6h i dont know if this is the same. came off a 308 non efi with a eaton m90 supercharger with complete fuel injection. it is fully programable but you need an older laptop to make it work.

when i turn on my air con vs 5lt ute it works for about 30 seconds then the belt starts to squeal. had a look but everything looks good. is my compressor shot or if i spray some crc in the front will this hurt anything.

one thing i found to change was the wiper motor. a nice small one of a jap works well. made adaptor plate to original holes.no drilling. also if you had a drum front end like i did,it is cheaper 2 buy one ready to go than rebuild one. go with one that will have holden stub axles & commodore...

is it a problem all the time or only when you drive it first thing. within bout 2 min driving time dont matter if you got heat risers attached or not . it grts pretty fugin hot. did u have the carby overhauled before or after fitment of rackies.

has anyone had much to do with haltech cpu. what i got is a m90 supercharger that runs fuel injection on a modified manifold for pre efi 5lt. got an aftermarket wiring loom that came with it that runs only oxygen sensor,map sensor, water temp sensor & one that runs off your flex plate. what i...

ist got a msd 6al billet msd distributor with a blaster coil. only the basics & it has all new wires run everywhere. the speaker wires run down the tunnel of me ute & amp is behind the seat. im pretty sure the wires dont cross but if the aerial wire came close would this make a difference.

here are some pictures of my eh sdn. had if for about 3 years but am trying to serious on it to finish by december for me mates wedding. got a 202 fuel injected black motor with but instead of injection put on a x2 twin carb manifold with x2 headers.got some 15 standard wheels to fit with the...

this is a 6cyl yes. did u remove the carby the base gasket may be leaking also did u replace all the hoses corectly. some times it could be a split hose they look fine but on closer inspection domage has been done on removal.

why does the trigger sound from my msd 6al come through my front speakers.as the motor revs the sounds get louder. msd is in the glove box . no wires near each other, it has a suppressor to my amp but it wont go away.any sugestions. in a HQ ute 308:bang::bang:

ripsaw not sure how to get youtube here type in ripsaw if no one has done it already. i want one. if some one can point me in the rite direction on how to bring it up that would be good or you could just put on here:thumbsup:

timing is too far advanced or it is leaking fuel in the carby. has it got a 350 holley on it. happened to me before

If you can get the photo off your phone onto your computer, there is a section when you go to post a comment in a thread to "Manage Attachments" then its just a case of finding where you saved the image to on your computer, selecting it and following the prompts and it will upload it:thumbsup...

this it me rottie 3 years ago like i said is the best mut anyone could askfor.his birthday is next week.

A mate of mine built a 355 with a vortech blower & intercooler in a genuine GTSR that had water injection. my understanding is that it goes in just before the manifold or blower (cant remember) but it cools your engine gives it more oxygen plus it boosts compression-water dosn't compress.it had...

exhaust fabicator/fitter. been doin it for 12 years like mast jobs it has its moments. its good fun to take a car & make it sound different/louder/quieter /deeper note/ i want to hear it scream. never a dull moment. lookin to start me own buisness next couple of months so it will be fun fun fun

what a waste of an ek holden.dont know why someone would do that with a vn commie. what a waste of a australian history

yes it hurts i wen from riding a postie bike to suzuki ts185 trail bike to a FZR600 yammy while on my p/bout 5 years ago. best thing i ever did but not recomended for everyone. had more stacks & hit more cars than days of the week (5 times come off 2 hit cars) & most of the time it...

always good to see the oldies.building an EH sdn at the moment with twin stromise on it. would put tripples on it but with the price of fuel these days ya get down the road there goes $30

got a rottie about 3 years ago & love him more than me car. awesome pet best $500 bucks i ever spent. sure he digs holes/ eats my shoes & socks/ snores louder than my wife but i wouldnt mant any thing else. mine was the runt & has a huge personality,wouldnt hurt anyone. tried to put a photo on...

you still got air in the line. dose it just go strait to the floor or if you pump the pedal do you get anything

they go in through the bottom on both sides. what brand of extractors are you trying to fit. some are a lot easier than others

never had a problem fittin pacies ever.i guess it comes down to knowing what to do i spose. i fitted a set to my vs5lt ute after work done in just over 2 hours. i dont know anyone over here who fits hi tech headers. have a look at the two products side by side& tell me which ones you would put...

seen one at the kwinana motorplex couple years ago doin burnouts. not sure if it had a 5lt or 350 but it went hard. even whooped some of the new commys down the strip. wonder what happened to that volvo

Hk. came out with 307 (327 bathurst) chev HT. HG both came out with 253 308 (350 bathurst). iv never seen 308 hp block. only 179 hp

go for the twin 3 inch.if you get it for that price absolute bargain. x pipes are over rated

cant go past a torker manifold. They work well just wack on a 2 inch spacer & it should still fit under your bonnet. carby double pumper or vac secondry

still think pacey are top of the food chain. you cant beat what is proven. iv fitted a lot of sets & when you find something that works you stick to it. do they still have those slip joins they had before. havnt fitted a set of those in a long time. me an exhaust fitter in perth. wavez where...

its not a m90 but is very similar. thanks for that its given me some good ideas thats for sure. should go good in my EH sedan

Hi-Tech headers are good.you cant go wrong with the price. will cost you more to get them fitted than you paid for them. unless you fit them yourself .they come with a y branch or just 2 extractors

for every 4litres of fuel you burn your car will produce 1 litre of condensation.I have taken 2 litres of water out of a muffler many times. not through leaking head either

cat converters worth $80 bucks to someone who recycles them. if they tell you they arnt worth much they dont know what they are talking about or are trying to screw you. european cats are worth about $100 because there is more in them

some of the old hp blocks could be bored 220 thou as to 60 thou that used to make them wanted (also made them time bombs) as for high or low compression all six cyl came with that option. holden 202. 149 high compression head. ford 250 pre crossflow crank with starfire rods. decent carby in a...

Hi everybody.I want to know if anyone out there has fitted a eaton m90 supercharger(vt supercharged v6) to a vk black motor. i have some ideas but if someone out there in internet land could help that would be appreciated. yes i know there are other posibilities but to try something...

My hq holden ute has a 308 MSD ignition & believe it or not it runs at 18 degrees advanced.Dont know why asked a lot of questions. Depends on how much work it has i spose

cost has a small part to do with it.what i really want to know is there a power difference between the two. I have been told that with a mixer it will backfire & blow up the air box. Dose one have more problems than the other.

I want to know if anyone out there has had LPG injection fitted to their car. i have a 5lt vs ute and am contemplating which one is better. one is more expencive than the other but i want to know if it worth it. $3000 conventional lpg. $4500 lpg injection