Search results

Thanks for that. I will just wait until the fault stays up

Hi all, I have a vz ss commodore. A few times now the svs message appears and then resets itself. I took the car to holden for a scan, they said there were no error codes present, and to bring the car back when the message is their. The problem is that it resets itself. Any advice would be...

Thanks for the help. I got on to a holden dealer spare parts in melbourne who was very help full. The part number for the rear springs out of a 2009 calais sportwagon is 9223266. The front set is fe1. The front spring number is 92225233. These springs are also used in the statesman. Thanks...

Thanks for the offer but the springs I am after are the fe1 springs. they were original in my car. Cheers Baroofy

Hi all, I am after a front set of original springs for my 2009 ve calais sportwagon v8. I believe the holden part number is 92261933. Is this correct and has any body got them for sale. Is there any ather part number they could be. 92225233 ? Thanks for the help

Hi all, I have just bought a ve 2009 v8 calais sportwagon. The sportwagon has been lowered and I wish to bring it back to original height. My question is are the springs out of the v6 the same springs in the v8 and what are the Gm part numbers. Any help would be great. Cheers Baroofy

Thanks for the advice. I will check them. I t might save me a few bucks. Cheers Mick

Thanks for the info. What brand were the plugs and leads. Cheers Mick

Hi I am due to put new plugs and ignition leads on my VZ SS 6 ltr holden crewman. My problem is that some leads sets say they are the same ones as the 5.7 ltr. Is this true, or is the difference the length of the lead. Any clarification would be very helpful. Also are Eagle leads E88766 any...

Hi i have just installed a sony bluetooth stereo to my vz commodore. The radio works fine but there is an intermittant fault when you turn the car engine off, the dash illumination lights either come on or flash. When i turn the radio off or open the door it stops. Is this an earth fault? Has...

Hi, i have just fitted a 2nd hand tow bar to my vz wagon. I want to mount a flat trailer plug under the rear plastic bumper. but i am not sure where to run the wires from the plugs in the right rear to the trailer plug underneath. (are there any pre drilled holes). i prefer this set up compared...

The problem was an earthing problem. when i re eathered both O2 sensors and the right hand O2 heater wire the problem went away. the exhaust is a lot cleaner, fuel consumption is a lot better and the error code has gone. Thanks for the help and advice Baroofy.

Thanks for the quick replies. I will fix the earth problem first.

I have a vs series 2 commodore, error code 76 air/fuel ratio.new leads,plugs and fuel injectors fitted. still same code. (right bank richer than left) When checking O2 sensors these were the results i got at the ecu terminal 15 & 13. Left side ignition on 0 volts (with the sensor unpluged...

Thanks for the feedback. I will check the plugs when i get a chance (not able to check them for 2 weeks). The fuel consumption is high, about 400 km per tank (freeway driving). The plugs were replaced when the injectors were cleaned (insitue cleaning). Then the O2 sensors were changed then...

Hi was wondering if someone could help me. A while ago i had extractors and a new exhaust fitted to my vs. I also fitted a holden supercharged air intake with a k&n pannel air filter. After this i noticed that the exhaust was black and sooty. I the had the O2 sensors replaced and the cooling...

Thanks for the reply. Everything is standard . Today, everything has been working correctly. it was out in the rain when this problem happened.

last night when i turned off my car and lights, the parker and dash lights did not turn off.i had to pull out a fuse in the engine bay to get the lights to go out. i was wondering if any one has any idea on this problem. thanks.

i have just bought a vs series2 equipe. i was looking under the car to see where the lifting points are located so i can lift it on my hoist. i had no problem with the front points, but the location of the rear was confusing. the left rear side was ok, but the right side had some steel tubing...

i have just replaced the wire from the alt. to the battery and feed to the fusable links. the insulation at the fusable link was melted. i had to replace the fusable link holder as well as all the plastic around the main feed was burnt and melted. is this a common problem? i put a tong meter on...

g day thanks for the reply i live sw of sydney, mittagong way thanks

i have just bought a vs equip and i was looking at putting hurricane extractors and a 2.5 inch exhaust. i was wondering if any one has had any bad experiences with them, or are you happy with them thanks