93 exec VP-155000k.
Put new radiator and hoses in last yr due to blown water pump. Done the link pins and bushes bout 3 months ago. Runs and drives well.
15 0202 is stamped on them. Excuse my lack of knowledge......." are these front or rear shocks?" lol if there is anything missing, what is it an can I get the missing part without buying a whole new set?
Hey all,
Found these in my mates garage....... He reckons just take what you need......score!! Will these fit a 1993 VP exec?? Only thing is, is there something missing from them?? Shocks are the same so I'm not sure.....
Hey all,
I have just installed all my gauges and just want to know where these two wires are inside the car. I assume there are factory ones that I can use. Cheers.
Hi all,
I've got some used parts that I pulled off my brothers car before he gave it to his mate.
1. VT V6 recond alternator -$50 (firm)
2. VT V6 used coil packs and module - $50 for all 3 + module (firm)
3. VT V6 auto stage 4 chip - $35 Was never used but doesn't come in the retail...
I put a tach in my vp exec not long ago. I used the brown w/red trace from the wiring loom on the drivers side under the dash. Easy as if you take the covers off under the dash, works fine.
Got another one for ya, which wire is the water temp inside the car?
And if there is one, is there a oil pressure one or do I need to install the sender unit before installing te oil pressure gauge? Cheers
My 93 VP executives roof is fading and when u rub it, it's like a fine sand comes off. What's this?
Does anyone have a contact for a good, reasonably priced body/paint shop in brisbane?
I was told that you have to take out the whole dash.......? Gotta be an easier way though. Mine started leaking late last year, so I just by passed the heater tap etc so no coolant was leaking into the drivers aide footwell. Gonna have to get it fixed before summer comes along though.
hey all,
just wondering if anyone has installed one of those DIY Air Intake mods?
I have seen heaps of them on eBay......so I bought one:)
It claims to increase HP by up to 20HP......in conjunction with other mods.....of coarse.
Its instructions say to install it into the Air Intake...
Hey all.
I just installed a tacho in my S2 VP executive and wanted to know what the rev range is? I took it for a spin and at 4000rpm it sounded like it was screaming! The tacho is set to the 6 cylinder setting........
Just a question on how the @&$&&@&$ you get wire through the firewall?!!!!! I got a 1993 VP Executiveand putting in some gauges and want to do the wiring as tidy as possible.
I tried going through where the main wiring loom goes through but it's tough as he'll to get into!
Any suggestions...
Is 27mm sway bar a good size?
I've also been told that I have to put in an adjustable panhard rod ...... Is this true?
Looked up the corvette servo and it looks like a simple change, once I get the trans out :)
I'm also thinking of getting High ratio rockers. But that's a bit further down the...
Yea, didn't want to go super low. I've got a full set of new bushes to go in and looking at the sway bars.
Brakes are in line for the upgrade, slotted rotors but whats the best (and cheap) caliper upgrade? Should I go for the VP V8 set up, I've been told that the VT calipers were better??
Excuse...
I've had my VP for 4 yrs now and has been very reliable. I have only just started thinking about getting some work done on it. First thing on the list is a full body touch up, rust around boot and front/rear windscreen. I want to keep original colour ( blue/grey), as well as the V6. I have got...