Just Commodores Forum Community

It takes just a moment to join our fantastic community

Register

V6 ideler? Sqeek

Discussion in 'VR - VS Holden Commodore (1993 - 1997)' started by 1_johnboy, Apr 8, 2011.

  1. 1_johnboy

    1_johnboy Member

    Messages:
    411
    Likes Received:
    1
    Trophy Points:
    16
    Joined:
    Mar 7, 2011
    Location:
    east gippsland
    Members Ride:
    11` VE Omega
    I have a Squeek under bonnet, I have replaced the 2 ideler pullys above the AC pump including the waterpump. Did these as the sound seems to be coming from that side of the motor. But sound still there.
    Now I`m thinking the tensioner pully (all though sound dosent seems to come from that side of the motor) I have removed it and sprayed WD40 into it to see if it changed the tone of the squeek. Didnt seem to.
    I have tried to run the car without the belt and noise isnt there. I did notice that with the belt off and pull down on the tensioner it seems to squeek and have some sideways movement...dose this sound right? If not is it a replacable item, I cant seem to find any info on replacing it.
     
  2. 1_johnboy

    1_johnboy Member

    Messages:
    411
    Likes Received:
    1
    Trophy Points:
    16
    Joined:
    Mar 7, 2011
    Location:
    east gippsland
    Members Ride:
    11` VE Omega
    So have found the source of the noise. Its coming from the harmonic balancer. I would assume a balancer thats shagged would bang and knock but not sqeek..and sqeek alot. Is this a normal noise (of a shagged one)as I havent had anything to do with one on the way out.
    Balancer looks good, isnt moving about . Is there something behind it that could be causing it?
     
  3. hako

    hako Donating Member

    Messages:
    8,019
    Likes Received:
    84
    Trophy Points:
    48
    Joined:
    Aug 1, 2004
    Location:
    Toowoomba SE QLD
    Members Ride:
    VS11 BT1 V6
    Saturate it (well, spray it) with oil and see if it stops squeaking. Nothing behind should cause it....possibly it has sheared and the rubber is moving making a squeak although usually you can see them wobble (with belt on). Could also be a dry/old belt that is squeaking...spray water or chalk on ribs and see if it quietens it. I'm getting old/dry myself but find beer improves things, but I don't reckon you should waste beer on the belt, use water.
     
  4. 1_johnboy

    1_johnboy Member

    Messages:
    411
    Likes Received:
    1
    Trophy Points:
    16
    Joined:
    Mar 7, 2011
    Location:
    east gippsland
    Members Ride:
    11` VE Omega
    I`ll try a belt today, rubber from the out side loks good. Trying to move the outside of the balancer by hand shows no movment
     
  5. 1_johnboy

    1_johnboy Member

    Messages:
    411
    Likes Received:
    1
    Trophy Points:
    16
    Joined:
    Mar 7, 2011
    Location:
    east gippsland
    Members Ride:
    11` VE Omega
    You were spot on mate, belt was causing it. I've never heard of a belt making that noise. I still think the tensioner arm is shagged. Is this a replaceable part, if so how is it done and what are they worth?
     
  6. hako

    hako Donating Member

    Messages:
    8,019
    Likes Received:
    84
    Trophy Points:
    48
    Joined:
    Aug 1, 2004
    Location:
    Toowoomba SE QLD
    Members Ride:
    VS11 BT1 V6
    The tensioner is replaceable...cost upwards of $200 and take a few hours to fit but not impossible. Most tensioners seem to squeak and move quite a bit when the engine is running. I'd leave the tensioner till I was absolutely sure it is shagged.
     

Share This Page