Just Commodores Forum Community

It takes just a moment to join our fantastic community

Register

VH Holden dash loom

Discussion in 'Electrical Wiring / Questions' started by Ash.Mcdonald, Sep 6, 2019.

  1. Ash.Mcdonald

    Ash.Mcdonald New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 2, 2019
    Location:
    Christchurch New Zealand
    Members Ride:
    83 vh. 96 vs. 98 vt.
    Hi guys
    Apologies in advance if this is an already asked question I couldn't find a post anywhere.
    I am installing the interior loom in my VH just wondering if anyone has a picture or diagram of were the loom should sit under the dash I have currently poked it all through the triangle holes on the bracket above the steering column and run it down the channel on the brace once done I realised there is a clip to hold it up somewhere but will that be good enough to leave?
    Sorry for a dumb question,bloody Kiwis ae
    On the note of dumb questions does anyone also have a diagram of how all my heater plastics piece together I have a book but it doesn't really tell me much in regards to how it all goes

    Thanks in advance
     
  2. !Miffy68!

    !Miffy68! New Member

    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 9, 2019
    Location:
    Bacchus Marsh
    Members Ride:
    1981 VH SLE
    Hi I have my dash out if you want a photo.
     
  3. Ash.Mcdonald

    Ash.Mcdonald New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 2, 2019
    Location:
    Christchurch New Zealand
    Members Ride:
    83 vh. 96 vs. 98 vt.
    That would be great thank you
    Can you add to here or you need my email?
     
  4. !Miffy68!

    !Miffy68! New Member

    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 9, 2019
    Location:
    Bacchus Marsh
    Members Ride:
    1981 VH SLE
    Hope this helps, if you need more ask.
     

    Attached Files:

  5. Ash.Mcdonald

    Ash.Mcdonald New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 2, 2019
    Location:
    Christchurch New Zealand
    Members Ride:
    83 vh. 96 vs. 98 vt.
    That's great thank you, you couldn't take one lower of the wiring into the steering column
     
  6. !Miffy68!

    !Miffy68! New Member

    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 9, 2019
    Location:
    Bacchus Marsh
    Members Ride:
    1981 VH SLE
    How's this. Also do you know were the red and orange wires at the top go and what is the relax thingy on the firewall behind the dash. Cheers Mark
     

    Attached Files:

  7. Ash.Mcdonald

    Ash.Mcdonald New Member

    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 2, 2019
    Location:
    Christchurch New Zealand
    Members Ride:
    83 vh. 96 vs. 98 vt.
    Perfect thanks mate.no sorry Iv only just managed to get my loom half in I haven't found them yet. I'm in the process of building the car but I wasn't the one that pulled it apart so struggling to work some of the wires out
     
  8. !Miffy68!

    !Miffy68! New Member

    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Joined:
    Sep 9, 2019
    Location:
    Bacchus Marsh
    Members Ride:
    1981 VH SLE
    LOL, I'm fixing the car for a friend in Tassie. I have to replace a cam shaft yet as the engine backfires up thru the carby.
     

Share This Page