vt codes

[adamandtanya]

just diagnosed my car it comes up with codes 31 and also 92 everything apears to be ok how do i fix this any help would be great

 

[vyssls1]

code 31 Theft deterrent sensor

TROUBLE SHOOTING PROCEEDURE
#1 Ign on use a volt meter check voltage for 3-5 volts at terminal 9 9circuit 1221 (red/black) DLC connector and earth

#2 Faulty PCM

TROUBLE SHOOTING REMEDY
#1 If OK go to next step,if not OK check for open or short in circuit 1221

# Replace


code 92 Low Speed Fan

TROUBLE SHOOTING PROCEEDURE
#1 Check is code 31 present

#2 If engine does not start and code 92 is set,test circuit 1221 (red/black) for earth or open

#3 Check for intermittent fault in harness or connectors


TROUBLE SHOOTING REMEDY
#1 Treat code 31 and test drive

#2 Repair

#3 Repair or replace

 

[fasamr]

pleasem explain these error codrs

47 18X Reference Signal
Missing

32 Mass Air Flow (MAF)
Sensor Out ofRange

82 1-2 Shift Solenoid B
Circuit Fault

 

[accentstencil]

Code 92 will almost certainly be a faulty low speed fan relay.

 

[VTS5]

pleasem explain these error codrs

47 18X Reference Signal
Missing

32 Mass Air Flow (MAF)
Sensor Out ofRange

82 1-2 Shift Solenoid B
Circuit Fault

First 32 MAF , if u can try another unit.

 

[VTS5]

pleasem explain these error codrs

47 18X Reference Signal
Missing

32 Mass Air Flow (MAF)
Sensor Out ofRange

82 1-2 Shift Solenoid B
Circuit Fault

Then Code 82 ,Looks like tranny problem,

 

[VTS5]

pleasem explain these error codrs

47 18X Reference Signal
Missing

32 Mass Air Flow (MAF)
Sensor Out ofRange

82 1-2 Shift Solenoid B
Circuit Fault

And now 47 18X Reference Signal Missing; Check or replace Crankshaft Position Sensor, Wiring or Connector.

 

[fasamr]

How to replace 1-2 shift Solenoid b

guys help me out anyone changed their transmission shift Solenoid's, let me know the complete Procedure of changing Solenoid step by step PLEASE!!!!!!!

I three 3 faults after doing the paper clip diagnose
1. 32 Mass Air Flow Sensor
(No adjustments possible on this component)
Voltage Signal Out of Range
Sensor Faulty, Wiring or Connector
I dont know wat to do with it i bought a used MAF from e-bay and after replacing i get same error no matter dosent bother a lot but need to be fixed

2. 46 Direct Ignition System No Crankshaft Reference Signal
(Received by PCM when Engine cranks)
DIS Module Problem
Wiring or Connector (DIS Module Terminal D to PCM Terminal #D12)
Really no idea wat is it this error.


3. 82 1-2 Shift Control Solenoid Circuit Fault
Solenoid, Wiring or Connector.
This is the Error code which i give more priroty to be fixed First cause i dont have the first gear car Picks up from 2nd gear, i hate that and want to know how to fix it or how to change the solenoid.

Do i need to remove the the valve body to replace it , if yes than i have to get it fixed from some mechanic , if i can do it with out removing any sensitive things it would save me $$$.

i am completely stuck so guys help me out

 

[Ramsey82]

How do I get these codes from the computer in my VT Series 1. I seem to have an ABS Module unit **** itself, however, I'd like to see if anything else has gone with it.

 

[Ramsey82]

Error codes

I may have found these nifty error codes but how to determine what they mean is tricky. I found that t00 nu or something that looks like that. I get to code 24, 25, 26 and they have this -- next to them. WHAT DOES THIS MEAN?