Search results

was scratching around and found these. RX do a top mount kit View topic - Another RX Top Mount Supercharger happy customer. :: Bowtie V6 - 5th Gen Camaro V6 Tech Forum, 2010 Camaro V6, 2011 Camaro V6, Camaro 3.6l, Camaro llt My LLT RX Performance Top mount SC - ModernCamaro.com - 5th...

SV6 325 can you clarify ? did HP tuners go back to a factory tune ? Or has it been tweaked? Id hope it has been tuned, correcting the A/F 4th gear dyno run? Shouldn't it be 3rd gear? my bikes were always done in 3rd 641Nm's thou its up there good Its on my wish list for sure

Well actually OP, Raptor chargers (a forum sponsor) would be interested in your setup,as they are teasing the thought of making a kit for the sidi's down under at a competitive price. They are still looking for a donor car (not yours) that they can do a build on. But perhaps you two can share...

Good luck with the tune, I'm keen to follow your footsteps. Keep us posted

Don't want to hijack the thread, but I could not agree more with MACE. So helpful, when no one else seems to care, MACE help! Thank you for the tune and the tweaks.\ Best Wishes Rod

sort of sounds like its running on choke or rich. ECU issue perhaps? assuming the maf/intake temp sensors are fine.

if you do need a new maf sensor for VE series 2 sidi, hit me up! it's new and I accidently bought it.

Hi Op I have had a similar problem with a faulty ECU on my 2011 sportswagon. Bosch E69 ECU. I bought one from a commodore wreckers, but it has to be the exact model with right sequence number, talk to the wreckers (a good one will match one up for you) if you send the photos of the ECU sticker...

I go to NRMA or the RACV Vic equivalent workshop and they use the Havoline. (2011 sv6 25k kms) The engine's not using excess oil and seems to be fine each time.

thanks for the replies guys, my speedo shows the car is travelling slower than the actual dash reading when comparing it with a GPS measurement. Ok... I just asked because on Sydney roads the ride is pretty harsh so wanted more cushion. So would I be correct in assuming that: a)you would...

Sorry for a stupid question Is anyone running with 245/50/18 tires? Compared to the stock 245/45/18 on their ride? If not why not ?

Turned out to be at the junction at the battery feed into engine bay, you know where the Red + cap is top right of engine bay (near right shock tower) Apparently there's an inbuilt fuse in there somewhere, and after showing Holden mechanics, it went faulty on them too. They changed the whole...

Ok well that fuse works but whenever I move it, I lose power to the whole car.. That's a "send back to Holden" Warranty I assume, dam better be!

There is a 12v positive cable right near the fuse box, I was probe-ing that point to earth Initially there was no 12v, after moving the cable, measured 12v again WTF

Yesterday my near new car 18k kms on the clock car went into limp mode or no power/charge mode in traffic, like no power to anything no dash no nothing just dead. I know a little about electrical circuits, so I tested the known power points tested in engine bay and found this. Tested...

HI Didn't want to start a new thread, but.... Has anyone got charts on the....... before & after of cam installs for SIDI I would like to see some dyno runs before I drop $1300 on cams

Could you buy the SS caliper cariers from Holden spare parts? Was thinking about doing this also, Then upgrade the rotors and pads when the pads are due.

Thank you both Mace and sv6guy for your information. Will go with the 12mm spacer once im ready to purchase.:)

Thank you Isn't VCM a different brand of Cold air intake? Are you saying that a 12mm spacer will have better gains than the 6mm and that the whole MACE CAI will fit better using the 12mm Whats involved with panel service and what intervals would you be cleaning this?

Hi Mace, Im keen to get one of these units, just wanted to check a few things before buying. I've seen on other web forums that sometimes a vacum hose ends up too short? I'm confident of fitting it myself. but just wanted to know if anything would fall short once I install...

Another reason for scalloped rubber, is braking at speed in a turn. Tyres:: I pretty much have the same car (wagon) I was hoping the potenzas would be my next tyre, but i'll hold off until I do more research Yoko's: I would not recommend, far too loud Pireelli P6 safe in the wet, may...

Just had mine done also (15000km) $380 from the dealer i bought my car from... Crawford Holden brookvale $340 from my local dealer Muirs Ashfield so i went to NRMA service center 15000K logbook service $260 used havoline oil, GM approved oil Happy with everyhting so far..

Thank you Muke & RiCey I'll check out that doc Regards

Mmm are there any panel beaters or audio installers that may know the answer to my question?

hey man, i just swapped out all my door speakers with JBL's 6.5 inch i got 3ways for the rear doors got component / splits for the front added some sound dampening mats (not much) just in the area behind the speakers. Sound is seriously much better The JBL's (dont know how they do...

+1 on the noisy Yoko's mine produce huge noise

Hi All, I tried removing the lower part of the B pillar trim and split it (opps) It seems like its held in some sneaky way? Mine has three parts to it..... lower part that sits in between both the door wells (dark colour) A middle section that just looks like a box section (dark colour)...