Search results

Admin and Mods please delete this thread if you wish, I got the barb connector from a wrecker. Of note the VR and VS low pressure lines are different - VR being shorter and VS being longer, but both have the same thread - so all good here. Thanks

Hi all, I am putting a VS Commodore rack into a custom build. I have 2 questions. On the rack which outlet does the high pressure line connect to? and secondly The low pressure line is connected with a hose, does anyone know what size the fitting is so I can get a barb connector for it. Any...

Thanks.

Hi all Wondering what these 2 switches are on the L67. I found the coolant sensor near the thermostat housing and oil pressure switch near the oil filter but what are these 2 on the side of the block? thanks Jason

thanks

Hi all, I have this wire attached to the outside of the PCM loom, it has a plug on it and I was wondering where it goes, I was wondering if it was an earth. I have attached an image of it. If anyone know wheres it goes and what it does that will be appreciated. Thanks Jason

Thanks I will put a 5amp inline fuse on it. Yeah I have to run the battery down the rear now and will just put a joiner in it near the starter motor so it is easy to remove to pull the motor in and out. Thanks everyone for the help on this issue. Jason

All good, yeah I have to make a new cable as the battery is in a different spot now compared to where it would be in a VT. The question I was just asking basically is what size wire (3mm?) and what amp fuse should I put in it. Thanks Jason

Thanks - what size fuse would be best suited for this wire and since I will need to replace the wire as it will be to short, what size wire should I really replace it with?

thankyou.

Thank you both for your reply. Yeah I have a separate wiring harness etc from v6conversions.com.au for the engine harness etc but the only thing that I didn't know was that brown and white plug wire. This wont take too long to add to the existing harness. In regards to the white wire, I could...

Hi all, Doing a custom build of a L67 V6 from a VT Comm into a FJ Holden panelvan. I have attached an image of the alternator wiring. The question I have is the purple and brown wire plug. This plug the purple wire comes from the spade terminal from the starter. The brown wire comes from the...

ITEM: 1999 (March) VT Commodore black sedan. I bought this vehicle as a donor vehicle. For the build, I only require the motor, trans, ECU and wiring loom. As such every other part of the car needs to go LOCATION: Strathmore, Victoria CONDITION: Used PRICE: Negotiable or Make an offer...

thats the correct diagram above and the plug. Thanks

Thanks but the crewman plug is different.

Hi all, Does anyone have a wiring diagram for the VZ Crewman fuel sender plug. Any help would be appreciated. Thanks Jason

Thanks - yeah I have seen that top youtube clip before.

Can anyone tell me what the difference is between the V6 and V8 fuel sender units are in the VZ crewman. Are they different sizes physically or are the pumps different?? If possible does anyone have the part numbers for these items. I am after a V6 crewman fuel sender assembly. I think the...

thanks exactly what I am after.

Hi all, I am after information about what range the VZ crewman fuel sender unit ohm range is. I would like to know the range as I am setting this fuel sender unit up to a VDO fuel gauge. Any help would be appreciated. Thanks Jason

No went to scrap metal weeks ago.

Just done this just need to remove linkage from transmission.

thankyou for the information

I am wondering the same question as a family member needs a starter motor for her VT but I have a few VP starter motors.

yes we have a vn v6 series 2 motor and trans - what are you after the whole motor or individual bits and we have another series 1 with trans in the shed we want gone as well.

ITEM: VN Calais LOCATION: Lara, Victoria - Lara is between Geelong and Melbourne PRICE: Currently wrecking a VN Calais. We acquired the car as we are putting the electrics and interior into a VG ute. the items for sale include VN Calais wheels, leather rear seat, rear doors, boot lid...

RIP no problem re those parts, I just need to sus out the length of those strips and work out best way for posting, so they dont get damaged. You can have them both for $10 plus post. IMPULSIVE $35 for both posted

$150 for bonnet and bar. I'd rather sell the seats complete, than pull them apart, I do have interest in one of the seat air bags though, if it sells then I will part the seat out, do you have a pic of the exact part? Is it the piece you move to adjust the seat? Contact made re mirror.

Have you tried hooking up a fuel pressure guage?

Still have number plate surround available. Cd player is single, do have pin. Bonnet $100, head lights $30 each. Front struts $40 each. Seat belt is good $35 including postage.

I have one in wollongong

Need the o2 sensors, sorry.

I'll have to check the seats, I think they do have airbags. Headlights will be $80 including postage. I'll give harlzz a chance to reply about the mirrors as he has requested them.

No worries Gus its clear now, tomorrow is fine.

Mirrors are black, $20 each plus postage

Sorry for late reply guys, didn't realize they were banking up! Engine is 10hba 160k still able to drive to test if required, will need to change over sump, one on it is damaged. $1200 $25 for grill, $30 each for headlights, plus postage. Right tail light is damaged, left one $30 postage...

$40 including postage for interior bits, re the seat belt I have someone interested in the seats as a complete unit so I'll wait and see how that goes before pulling parts of them.

Condition of the wagon shell is perfect, it is a statutory write off, so cannot be registered, depends what you need it for. Once I have the parts I need out of it you can have the rolling shell for $500, it was minor fresh water flood damaged.

Gus, can you clear your inbox?

Interested in a rolling wagon shell?