Search results

Just installed both intake spacers and PCM from mace (stock exhaust) . Amazing to drive... Gear changes are twice as fast (auto). No longer bogs down. shes a completely different car to drive. the shift from 1st to 2nd gear is unbelievable it just keeps pulling. Also when revved in neutral there...

Unfortunately not. Check out the link below. https://www.youtube.com/watch?v=a1kITxtjKRg "This run was testing the Mace Engineering 12mm plenum and 25mm manifold spacer and a cold air intake. It made 114rwkw" If you had nitrous you would see 200kw at the wheels no problem.

The Clutch Grommet if you have an auto, its right where the clutch peddle should of been. Easily fits 0 gauge no problem.

Yes 6.5 fit no probs, not to hard to do just need to remove door trims swap speakers out, find a nice place for the crossover. routing the cable through the door can be a bit tricky. Sounds best if you mount the tweeters in factory position. Amplified is always going to sound better. Will have...

Hey mate, You will want to wire your sub in parallel which will make it 2ohm Pioneer Mono Block amp for the sub - 800rms @ 2ohm - $320 - (Does 1200rms @ 1 ohm so if decide to get another sub it would go well) Pioneer GM-D9601 Mono Block Amplifier | RYDA Car Audio Pioneer 4 Channel for...

Kenwood DDX470 Headunit Amps: Hifonics BRX2400.1 x 2 / 2400rms x 1 @ 1ohm Hifonics BRX1616.4 / 200rms x 4 @ 4ohm Speakers: Front: Soundstream RF-60.C Splits 180rms Rear: Alpine Type R SPR60 Splits 110rms Subs: Soundstream SPLX15HF 1250rms x 2 I have the front channels tuned to...

Hey matey, The OAX801 is a subwoofer amp, not for speakers. The TS-A1674S speakers are rated for 35RMS so they dont need much power. In the option audio range you can pickup the OAK75 4 channel speaker amp which is what you need for speakers, its only $120 brand new. the OAK75 puts out 75RMS...

I'm assuming your price range is below $350. I have Alpine type R splits in my rear doors (Use to be in the front) which I paid $320 for... I later upgraded to Sound stream Reference Splits which set me back $350 and honestly they literally Sh*t all over the Alpines. The Alpines are rated for...

Your fusion amp and sub combo are fine... Sub: Powerplant 12" sub Amp: Fusion - PP-AM20001 Check all your connections and make sure nothing is shorting out, especially the Ground cable. That Kenwood amp (Only 950rms) doesn't put out as much RMS as the Fusion one. That shop you went to are...

The gain setting is dependent on the headunit. Some H/U only needs the gain to be set at 20%. Mine (A shitty sony xplod) needs to be at 55%. A good way to tune the sub is have the Headunit volume at say 85% - 90% then slowly turn the gain up until it is as loud as the sub can handle. You will...

Hi, I want to run 2 monoblock amps, one amp per sub. I currently have 1 x 2100rms @ 1 ohm amp and 1 x SoundStream SPLX15-HX sub which is rated for 1250rms. If I were to get an additional 2100rms amp is there a better sub combo I could be getting? I can pick up another SPLX15-HX for...

I didn't read the question properly... To answer your question you probably had the gain set to high and the excessive heat has cooked the coil. Like I said that sub should be able to handle 600rms.

That sub and amp will run with each other without any worries. That sub could probably handle 600rms @ 2 ohm with no dramas. For the money your paying though there are better options out there. I would recommended you just save your money and get a bass setup in excess of $1500+ Better to...

Did rear the thread properly. Whats your budget?

Thank you all for your input. the 0 gauge fits nice and snug. Clutch grommet was easy to get out and put back on. Just have to pop it out from the inside of the car (after removing that plastic cover) just above the pedals. Bass is louder now :) and 0 gauge looks awesome plugged into the amp.

That alpine amp will power it fine.

Cheers guys. I went with 0 gauge. Picked up 5 meters for $75 inc gst. Seeing as my car is auto can I feed the 0 gauge through the clutch grommet? or is there a better place? Thank you.

Hi, I have a 2000rms monoblock. I already have 1 run of 4 gauge from the battery to the amp. Is it any good to run 1 x 4 gauge to the 4 Chanel amp and 2 x 4 gauge to the Mono block? I thought I may just use my T distribution block and have 2 x 4 gauge running into that and 1 wire going...

That is so hot ammojammo!! What are my options for a dual batt setup?

#### yea man! What model are your subs? I think they are pioneers, correct me if im wrong :p

Mad, thank you! I'm not a fan of 2nd hand I have always bought brand new.

Fire insurance aye?? That sounds like a good idea! My wagon is insured for $12500, I could go back and buy a VS again, that beast will be pumping with a $10k system lol. 0 gauge.. I was afraid of that. Would it be better if I add a 2nd battery in the boot running of the 4 gauge? then 0 gauge to...

Hi, I wish to make some big bass with a small budget. All I need is a monoblock, subs and a box. This is what I have so far: 2100rms @ 1ohm amp BRZ2100.1D $300 2 x Earthquake DBXI-15D (750rms each 4ohm DVC) $600 Shipping for subs and amp...

Fusion 4 gauge ring terminals and fork terminals are really good. You can't crimp them with pliers, you need to use a vice.. I think they are just over 1mm thick.

Yea man. Sweefu what do you think? Is your sub ported?

Anyone use this yet? Nic92 make a Bass vid with this track. You will see some real windscreen flex :D

Been like this since I got ADSL 2+ with optus. $99 > 1000gigabytes a Month :D > Unlimited phone calls to landlines and mobiles within Australia

If it's only the 1 amp, 8gauge will just be enough. Ideally you want 4 gauge, it's the best starting point when you get into car audio.

Test your system from 20 to 50hz Bass Tester 20 - 50hz.mp3 Scanned with virus total https://www.virustotal.com/file/e0c0dbe069bb3213dc9a9c1d09c64d393e43f3d4b7d5206fd6e752e6708ab394/analysis/1329074714/ It's a 128bit track at full volume. Only have your system at half to start with. The...

Pussaaaaaaaaaaaaaaaaye!!!!!!!!!!

Aye. I overpowered my Kicker Comps as soon as I got them. I wanted to see how loud they got, No worries lol. I did notice they got a bit louder over the next couple of days. I wasn't pumping them for hours at a time mind you. Mabey only a minute or 2 of a song. "flat out or nothing."...

The only thing wrong with Alpine is their prices. The 6x9 Alpine type R's have a rather small magnet and the frequency response isn't that great for 6x9's (60hz - 29khz). If you can pick up a new set for $150 you should get them (the new model that is)...

Couldn't find a guide. Yea you have to solder wires on the factory circuit board. There use to be a guide in the how to section but I think they took it down just like the led light dash conversion guide :( Sorry I can't help any further. Good luck finding one.

Whats wrong with xplod.... rofl

Model number plz.

I can only find the VY one sorry http://www.brain4arab.com/lumina-PDF/StereoModInst_rev1.1.pdf It's a **** job thats why people will point you to ASR audio. Phreddy from ASR charges $175 installed for the mod. Welcome to ASR Audio & Electronics Home Page

You have to solder the circuit board on the factory headunit. I'll find a guide and post it here one sec.

What did you end up doing whitesac?

The amps and sub sound really good. You can get way better speakers then those JBLs. Get a nice pair of vibe slick splits ($130) or black air splits (unsure of cost). I know from experience Vibe sound really nice. I have a set of Alpine type R splits in my car and the Vibe blackairs splits ****...

The OptionAudio OAK1200 amp does 1200rms (rated) at 1ohm and 700rms at 2 ohm, It will run these subs nicely. Wire all your subs in parallel and you will get a 1.3333333333 ohm load. Wire the subs like this: You can buy the option audio amp for around $350, they will be advertised at...